When a new object does not perform to its rated efficiency, customers rarely think it is because it was improperly installed; they blame it on factory faults or damage during delivery. High-efficiency gas furnace installation, if done correctly, reduces home energy consumptions and forced air zone controls save money. The necessary procedures and steps of properly installing a furnace in an existing house are given below.
For a successful installation, a process consisting of 4 steps should be followed. The first step of the process is called the pre-Changeout phase; this is performed before the purchase of the furnace and other sub-elements. A contractor responsible for the installation project has to check the old system and take necessary measurements and give the homeowner a quote of how much the project is going to cost. The contractor can t give a quote before assessing the old system, if they do then they might overcharge or undercharge the homeowner.
Pre-Changeout is a form of transitioning stage between the old and the new furnace system. The contractor will check how the old one was working, were improvements are needed and calculate how much energy output the new one should release, this is normally done during heat load calculations. Furthermore, the contractor will take measurements of the old system s ductwork, the new system has to have the exact measurements in order to be a perfect fit, otherwise, there may be air leakages.
The second step is called the installation phase. The newly bought parts and furnace are now ready to get installed. The furnace s manufacturer normally gives installation instructions, they are unique to every furnace. The contractor should follow those instructions during the process to avoid making mistakes. The rules in the Health and Safety Regulations Act should also be followed during the process.
When connecting the old ductwork to the new one, aluminium tape must be used to seal them to avoid air leakages where needed. Also, the furnace should be well levelled, otherwise the acid condensate released during the furnace operation may cause corrosion at a later stage. The opportunity of the air to flow at a turbulent from should be prevented during the installation process. That can be done by putting turning vines in the furnace and tapering where needed.
Once the furnace is installed, a certified gas fitter should be called to confirm and/or modify the new system so that it meets the manufacturer and the owner s performance requirements. This is the commissioning phase, the process involves checking individual system components like wiring and filters, checking the air pressure, temperature rise, static pressure and firing rate, and finally recording all these in a checklist before making the necessary modifications.
The homeowner should be given that checklist and if it shows that some modifications are needed, he/she should tell the contractor which installed the furnace. The last step should be taken by the contractor and it involves informing the homeowners about what to do when maintenance is needed, the warranty and how to use the furnace.
High-efficiency gas furnace installation should not be taken as a do-it-yourself project, certified contractors should be hired to complete the task. If they don t follow the above-mentioned steps then you ve chosen wrong contractors.
For a successful installation, a process consisting of 4 steps should be followed. The first step of the process is called the pre-Changeout phase; this is performed before the purchase of the furnace and other sub-elements. A contractor responsible for the installation project has to check the old system and take necessary measurements and give the homeowner a quote of how much the project is going to cost. The contractor can t give a quote before assessing the old system, if they do then they might overcharge or undercharge the homeowner.
Pre-Changeout is a form of transitioning stage between the old and the new furnace system. The contractor will check how the old one was working, were improvements are needed and calculate how much energy output the new one should release, this is normally done during heat load calculations. Furthermore, the contractor will take measurements of the old system s ductwork, the new system has to have the exact measurements in order to be a perfect fit, otherwise, there may be air leakages.
The second step is called the installation phase. The newly bought parts and furnace are now ready to get installed. The furnace s manufacturer normally gives installation instructions, they are unique to every furnace. The contractor should follow those instructions during the process to avoid making mistakes. The rules in the Health and Safety Regulations Act should also be followed during the process.
When connecting the old ductwork to the new one, aluminium tape must be used to seal them to avoid air leakages where needed. Also, the furnace should be well levelled, otherwise the acid condensate released during the furnace operation may cause corrosion at a later stage. The opportunity of the air to flow at a turbulent from should be prevented during the installation process. That can be done by putting turning vines in the furnace and tapering where needed.
Once the furnace is installed, a certified gas fitter should be called to confirm and/or modify the new system so that it meets the manufacturer and the owner s performance requirements. This is the commissioning phase, the process involves checking individual system components like wiring and filters, checking the air pressure, temperature rise, static pressure and firing rate, and finally recording all these in a checklist before making the necessary modifications.
The homeowner should be given that checklist and if it shows that some modifications are needed, he/she should tell the contractor which installed the furnace. The last step should be taken by the contractor and it involves informing the homeowners about what to do when maintenance is needed, the warranty and how to use the furnace.
High-efficiency gas furnace installation should not be taken as a do-it-yourself project, certified contractors should be hired to complete the task. If they don t follow the above-mentioned steps then you ve chosen wrong contractors.
About the Author:
When you are searching for information about forced air zone controls, come to our web pages today. More details are available at http://www.ewcestore.com now.
ليست هناك تعليقات :
إرسال تعليق